Skip to main content

Detailed Hardware Information

rx-888 teamAbout 2 min

Detailed Hardware Information

This document describes the hardware details to enable the user to do more experiment with the hardware.

FPGA Pin-out (PL Pin-out)

The following is FPGA pin-out definitions. They are all 3.3V CMOS.

set_property PACKAGE_PIN V17 [get_ports {adc_dat_a_i[0]}]
set_property PACKAGE_PIN U17 [get_ports {adc_dat_a_i[1]}]
set_property PACKAGE_PIN Y17 [get_ports {adc_dat_a_i[2]}]
set_property PACKAGE_PIN W16 [get_ports {adc_dat_a_i[3]}]
set_property PACKAGE_PIN Y16 [get_ports {adc_dat_a_i[4]}]
set_property PACKAGE_PIN W15 [get_ports {adc_dat_a_i[5]}]
set_property PACKAGE_PIN W14 [get_ports {adc_dat_a_i[6]}]
set_property PACKAGE_PIN Y14 [get_ports {adc_dat_a_i[7]}]
set_property PACKAGE_PIN W13 [get_ports {adc_dat_a_i[8]}]
set_property PACKAGE_PIN V12 [get_ports {adc_dat_a_i[9]}]
set_property PACKAGE_PIN V13 [get_ports {adc_dat_a_i[10]}]
set_property PACKAGE_PIN T14 [get_ports {adc_dat_a_i[11]}]
set_property PACKAGE_PIN T15 [get_ports {adc_dat_a_i[12]}]
set_property PACKAGE_PIN V15 [get_ports {adc_dat_a_i[13]}]
set_property PACKAGE_PIN T16 [get_ports {adc_dat_a_i[14]}]
set_property PACKAGE_PIN V16 [get_ports {adc_dat_a_i[15]}]
set_property PACKAGE_PIN P20 [get_ports adc_ofl_i]
set_property PACKAGE_PIN K14 [get_ports adc_pga_o]
set_property PACKAGE_PIN J15 [get_ports adc_dith_o]
set_property PACKAGE_PIN U18 [get_ports adc_clk_p_i]
set_property PACKAGE_PIN U19 [get_ports adc_clk_n_i]
set_property PACKAGE_PIN K18 [get_ports pps_i]
set_property PACKAGE_PIN G17 [get_ports {antenna_o[0]}]
set_property PACKAGE_PIN G18 [get_ports {antenna_o[1]}]
set_property PACKAGE_PIN H16 [get_ports {antenna_o[2]}]
set_property PACKAGE_PIN H17 [get_ports {antenna_o[3]}]
set_property PACKAGE_PIN J18 [get_ports {antenna_o[4]}]
set_property PACKAGE_PIN H18 [get_ports {antenna_o[5]}]
set_property PACKAGE_PIN F16 [get_ports led_o]

CPU Ports (PS Pin-out)

This section gives the detailed information regarding the chips connect to ARM CPU.

I2C Bus

There are two devices on I2C bus (i2c0). One is EEPROM and another is Si5351.

  1. EEPROM - Addr: 0x50 EEPROM stores lots of important information. Strongly suggest don't touch it. If you really want to use it, please backup the content first and use uboot-util to update the content.

  2. Si5351 - Addr: 0x60 Si5351 CLK0 is used as ADC clock as well as FPGA main clock. CLK2 is used for CLK out.

ATT chip

AD8370 provides tunable ATT on the RF path. The IO mapping is following:

AD8370_CLCK = IO_13
AD8370_LTCH = IO_12
AD8370_DATA = IO_11

Control IO

The following GPIO is controlling RF signal path. LOW - HF, HIGH - VHF.

SWITCH_HF_VHF  = IO_10

The following GPIO is controlling the reference clock of Si5351. LOW - External Clock Input (10M), HIGH - Internal TCXO (24.576Mhz).

REF_CLK_INPUT  = IO_49

Connectors

LeftRight

Anntenas (Up side)

  • HF Antenna

Connect to LNA with a 64M LPF.

  • VHF Antenna

Connect to LNA through a BPF centered by 129Mhz.

  • Reference Clock Input

Input a 10Mhz sine wave or square wave with 0.1-3.0 V p2p as the reference clock of Si5351.

  • GPS Antenna

Active GPS antenna with 3.3v bias power supplied.

Misc Connectors (Down side)

  • 1000MHz Ethernet

Support 1000Mhz or 100Mhz ethernet.

  • USB Host

Plug USB devices like USB Hub, USB Wifi Dongle, USB UART Dongle, etc.

  • EXTIO

Currently, the interface supports to use with Antenna swich extention. The pin definition is the following image. The GND pin is on the tf card side. The connector is SH 1.0, 8 PIN, male connector.

EXTIO
EXTIO

Warning

Although EXTIO connector is providing 5V power supply, GPIO is still 3.3V. All GPIOs are connected to FPGA directly. Please make sure you have the isolation and ESD protection.

  • USB-C Power Input

Make sure you supply a good 5v with 2A or higher.

  • TF Card Slot

TF card (Micro SD card). The card is inserted upside (lable side) down.